linux-2.6.16-rc5+imac-patch Edit

  • dmesg
    Linux version 2.6.16-rc5 (root@ubuntu) (gcc バージョン 4.0.2 20050808 (prerelease)
     (Ubuntu 4.0.1-4ubuntu9)) #1 SMP Tue Mar 7 19:53:19 JST 2006
    EFI: EFI v1.10 by Apple 
     ACPI=0x3fefd000 <6> ACPI 2.0=0x3fefd014 <6> SMBIOS=0x3fec9000 
    0MB HIGHMEM available.
    1022MB LOWMEM available.
    On node 0 totalpages: 261872
      DMA zone: 4096 pages, LIFO batch:0
      DMA32 zone: 0 pages, LIFO batch:0
      Normal zone: 257776 pages, LIFO batch:31
      HighMem zone: 0 pages, LIFO batch:0
    DMI 2.4 present.
    ACPI: RSDP (v002 APPLE                                 ) @ 0x3fefd014
    ACPI: XSDT (v001 APPLE   Apple00 0x00000039      0x01000013) @ 0x3fefd120
    ACPI: FADT (v003 APPLE   Apple00 0x00000039 Loki 0x0000005f) @ 0x3fefb000
    ACPI: HPET (v001 APPLE   Apple00 0x00000001 Loki 0x0000005f) @ 0x3fefa000
    ACPI: MADT (v001 APPLE   Apple00 0x00000001 Loki 0x0000005f) @ 0x3fef9000
    ACPI: MCFG (v001 APPLE   Apple00 0x00000001 Loki 0x0000005f) @ 0x3fef8000
    ACPI: ASF! (v032 APPLE   Apple00 0x00000001 Loki 0x0000005f) @ 0x3fef7000
    ACPI: SBST (v001 APPLE   Apple00 0x00000001 Loki 0x0000005f) @ 0x3fef6000
    ACPI: ECDT (v001 APPLE   Apple00 0x00000001 Loki 0x0000005f) @ 0x3fef5000
    ACPI: SSDT (v001 APPLE   SataPri 0x00001000 INTL 0x20050309) @ 0x3fec6000
    ACPI: SSDT (v001 APPLE   SataSec 0x00001000 INTL 0x20050309) @ 0x3fec5000
    ACPI: SSDT (v001 APPLE     CpuPm 0x00003000 INTL 0x20050309) @ 0x3fef0000
    ACPI: DSDT (v001 APPLE      iMac 0x00040001 INTL 0x20050309) @ 0x00000000
    ACPI: PM-Timer IO Port: 0x408
    ACPI: Local APIC address 0xfee00000
    ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
    Processor #0 6:14 APIC version 20
    ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
    Processor #1 6:14 APIC version 20
    ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
    ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
    ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
    IOAPIC[0]: apic_id 1 already used, trying 2
    IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
    ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
    ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
    ACPI: IRQ0 used by override.
    ACPI: IRQ2 used by override.
    ACPI: IRQ9 used by override.
    Enabling APIC mode:  Flat.  Using 1 I/O APICs
    ACPI: HPET id: 0x8086a201 base: 0xfed00000
    Using ACPI (MADT) for SMP configuration information
    Allocating PCI resources starting at 10100000 (gap: 10000000:00400000)
    Built 1 zonelists
    Kernel command line: BOOT_IMAGE=atapi2:\vmlinuz-2.6.16-rc5
                         video=imacfb:i17 acpi=force irqpoll root=/dev/sda5 libata.atapi_enabled=1
    Misrouted IRQ fixup and polling support enabled
    This may significantly impact system performance
    mapped APIC to ffffd000 (fee00000)
    mapped IOAPIC to ffffc000 (fec00000)
    Enabling fast FPU save and restore... done.
    Enabling unmasked SIMD FPU exception support... done.
    Initializing CPU#0
    PID hash table entries: 4096 (order: 12, 65536 bytes)
    Console: colour dummy device 80x25
    Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
    Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
    Memory: 1030720k/1047488k available (2767k kernel code, 13452k reserved, 776k data, 248k init, 0k highmem)
    Checking if this processor honours the WP bit even in supervisor mode... Ok.
    Oops: efitime: can't read time status: 0x80000007
    Using HPET for base-timer
    Using HPET for gettimeofday
    Detected 1833.334 MHz processor.
    Using hpet for high-res timesource
    Calibrating delay using timer specific routine.. 3678.19 BogoMIPS (lpj=7356385)
    Mount-cache hash table entries: 512
    CPU: After generic identify, caps: bfe9fbff 00100000 00000000 00000000 0000c1a9 00000000 00000000
    CPU: After vendor identify, caps: bfe9fbff 00100000 00000000 00000000 0000c1a9 00000000 00000000
    monitor/mwait feature present.
    using mwait in idle threads.
    CPU: L1 I cache: 32K, L1 D cache: 32K
    CPU: L2 cache: 2048K
    CPU: Physical Processor ID: 0
    CPU: Processor Core ID: 0
    CPU: After all inits, caps: bfe9fbff 00100000 00000000 00000140 0000c1a9 00000000 00000000
    Checking 'hlt' instruction... OK.
    CPU0: Intel Genuine Intel(R) CPU            1400  @ 1.83GHz stepping 08
    Booting processor 1/1 eip 2000
    Initializing CPU#1
    Calibrating delay using timer specific routine.. 3666.76 BogoMIPS (lpj=7333529)
    CPU: After generic identify, caps: bfe9fbff 00100000 00000000 00000000 0000c1a9 00000000 00000000
    CPU: After vendor identify, caps: bfe9fbff 00100000 00000000 00000000 0000c1a9 00000000 00000000
    monitor/mwait feature present.
    CPU: L1 I cache: 32K, L1 D cache: 32K
    CPU: L2 cache: 2048K
    CPU: Physical Processor ID: 0
    CPU: Processor Core ID: 1
    CPU: After all inits, caps: bfe9fbff 00100000 00000000 00000140 0000c1a9 00000000 00000000
    CPU1: Intel Genuine Intel(R) CPU            1400  @ 1.83GHz stepping 08
    Total of 2 processors activated (7344.95 BogoMIPS).
    ENABLING IO-APIC IRQs
    ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
    checking TSC synchronization across 2 CPUs: passed.
    Brought up 2 CPUs
    migration_cost=4000
    NET: Registered protocol family 16
    ACPI: bus type pci registered
    PCI: Using MMCONFIG
    ACPI: Subsystem revision 20060127
    ACPI: Found ECDT
    ACPI: Could not use ECDT
    ACPI: Interpreter enabled
    ACPI: Using IOAPIC for interrupt routing
    ACPI: PCI Root Bridge [PCI0] (0000:00)
    PCI: Probing PCI hardware (bus 00)
    PCI: Transparent bridge - 0000:00:1e.0
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEGP._PRT]
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT]
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP02._PRT]
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
    ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 10 12 14 15) *0, disabled.
    ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 11 12 14 15) *0, disabled.
    ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 10 12 14 15) *0, disabled.
    ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 11 12 14 15) *0, disabled.
    ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 7 10 12 14 15) *0, disabled.
    ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 7 11 12 14 15) *0, disabled.
    ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 5 6 7 10 12 14 15) *0, disabled.
    ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 11 12 14 15) *0, disabled.
    ACPI: Embedded Controller [EC] (gpe 23) interrupt mode.
    SCSI subsystem initialized
    usbcore: registered new driver usbfs
    usbcore: registered new driver hub
    PCI: Using ACPI for IRQ routing
    PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
    PCI: Bridge: 0000:00:01.0
      IO window: 2000-2fff
      MEM window: 88300000-883fffff
      PREFETCH window: 80000000-87ffffff
    PCI: Bridge: 0000:00:1c.0
      IO window: 1000-1fff
      MEM window: 88200000-882fffff
      PREFETCH window: 3ff00000-3fffffff
    PCI: Bridge: 0000:00:1c.1
      IO window: disabled.
      MEM window: 88100000-881fffff
      PREFETCH window: disabled.
    PCI: Bridge: 0000:00:1e.0
      IO window: disabled.
      MEM window: 88000000-880fffff
      PREFETCH window: disabled.
    ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 169
    PCI: Setting latency timer of device 0000:00:01.0 to 64
    ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 17 (level, low) -> IRQ 177
    PCI: Setting latency timer of device 0000:00:1c.0 to 64
    ACPI: PCI Interrupt 0000:00:1c.1[B] -> GSI 16 (level, low) -> IRQ 169
    PCI: Setting latency timer of device 0000:00:1c.1 to 64
    PCI: Setting latency timer of device 0000:00:1e.0 to 64
    audit: initializing netlink socket (disabled)
    audit(2254587648.636:1): initialized
    Total HugeTLB memory allocated, 0
    VFS: Disk quotas dquot_6.5.1
    Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
    Initializing Cryptographic API
    io scheduler noop registered
    io scheduler anticipatory registered (default)
    io scheduler deadline registered
    io scheduler cfq registered
    ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 169
    PCI: Setting latency timer of device 0000:00:01.0 to 64
    assign_interrupt_mode Found MSI capability
    Apple machine detected. MSI disabled
    PCI: MSI quirk detected. MSI disabled.
    Allocate Port Service[0000:00:01.0:pcie00]
    Allocate Port Service[0000:00:01.0:pcie03]
    ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 17 (level, low) -> IRQ 177
    PCI: Setting latency timer of device 0000:00:1c.0 to 64
    assign_interrupt_mode Found MSI capability
    Allocate Port Service[0000:00:1c.0:pcie00]
    Allocate Port Service[0000:00:1c.0:pcie02]
    Allocate Port Service[0000:00:1c.0:pcie03]
    ACPI: PCI Interrupt 0000:00:1c.1[B] -> GSI 16 (level, low) -> IRQ 169
    PCI: Setting latency timer of device 0000:00:1c.1 to 64
    assign_interrupt_mode Found MSI capability
    Allocate Port Service[0000:00:1c.1:pcie00]
    Allocate Port Service[0000:00:1c.1:pcie02]
    Allocate Port Service[0000:00:1c.1:pcie03]
    pci_hotplug: PCI Hot Plug PCI Core version: 0.5
    imacfb: framebuffer at 0x80010000, mapped to 0xb8900000, using 10350k, total 16384k
    imacfb: mode is 1440x900x32, linelength=5888, pages=1
    imacfb: scrolling: redraw
    imacfb: Truecolor: size=8:8:8:8, shift=24:16:8:0
    Console: switching to colour frame buffer device 180x56
    fb0: IMAC VGA frame buffer device
    Real Time Clock Driver v1.12ac
    i8042.c: No controller found.
    RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
    loop: loaded (max 8 devices)
    ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 169
    PCI: Setting latency timer of device 0000:02:00.0 to 64
    sky2 v0.15 addr 0x88200000 irq 169 Yukon-EC (0xb6) rev 2
    sky2 eth0: addr xx:xx:xx:xx:xx:xx
    libata version 1.20 loaded.
    ahci 0000:00:1f.2: version 1.2
    PCI: Enabling device 0000:00:1f.2 (0005 -> 0007)
    ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 185
    PCI: Setting latency timer of device 0000:00:1f.2 to 64
    ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 4 ports 1.5 Gbps 0x4 impl SATA mode
    ahci 0000:00:1f.2: flags: 64bit ncq ilck stag pm led clo pio slum part 
    ata1: SATA max UDMA/133 cmd 0xB881A100 ctl 0x0 bmdma 0x0 irq 185
    ata2: SATA max UDMA/133 cmd 0xB881A180 ctl 0x0 bmdma 0x0 irq 185
    ata3: SATA max UDMA/133 cmd 0xB881A200 ctl 0x0 bmdma 0x0 irq 185
    ata4: SATA max UDMA/133 cmd 0xB881A280 ctl 0x0 bmdma 0x0 irq 185
    ata1: SATA link down (SStatus 0)
    scsi0 : ahci
    ata2: SATA link down (SStatus 0)
    scsi1 : ahci
    ata3: SATA link up 1.5 Gbps (SStatus 113)
    ata3: dev 0 cfg 49:2f00 82:746b 83:7f01 84:4063 85:7469 86:3f01 87:4063 88:207f
    ata3: dev 0 ATA-7, max UDMA/133, 312581808 sectors: LBA48
    ata3: dev 0 configured for UDMA/133
    scsi2 : ahci
    ata4: SATA link down (SStatus 0)
    scsi3 : ahci
      Vendor: ATA       Model: WDC WD1600JS-40N  Rev: 10.0
      Type:   Direct-Access                      ANSI SCSI revision: 05
    ata_piix 0000:00:1f.1: version 1.05
    ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 193
    PCI: Setting latency timer of device 0000:00:1f.1 to 64
    ata5: PATA max UDMA/100 cmd 0x30E8 ctl 0x30FE bmdma 0x30C0 irq 193
    ata6: PATA max UDMA/100 cmd 0x30E0 ctl 0x30FA bmdma 0x30C8 irq 193
    ata5: dev 0 cfg 49:0f00 82:0000 83:0000 84:0000 85:0000 86:0000 87:0000 88:101f
    ata5: dev 0 ATAPI, max UDMA/66
    ata5: dev 0 configured for UDMA/66
    scsi4 : ata_piix
    ATA: abnormal status 0x7F on port 0x30E7
    ata6: disabling port
    scsi5 : ata_piix
      Vendor: MATSHITA  Model: DVD-R   UJ-846    Rev: FB2U
      Type:   CD-ROM                             ANSI SCSI revision: 05
    SCSI device sda: 312581808 512-byte hdwr sectors (160042 MB)
    sda: Write Protect is off
    sda: Mode Sense: 00 3a 00 10
    SCSI device sda: drive cache: write back w/ FUA
    SCSI device sda: 312581808 512-byte hdwr sectors (160042 MB)
    sda: Write Protect is off
    sda: Mode Sense: 00 3a 00 10
    SCSI device sda: drive cache: write back w/ FUA
     sda: sda1 sda2 sda3 sda4 sda5 sda6
    sd 2:0:0:0: Attached scsi disk sda
    sr0: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray
    Uniform CD-ROM driver Revision: 3.20
    sr 4:0:0:0: Attached scsi CD-ROM sr0
    sd 2:0:0:0: Attached scsi generic sg0 type 0
    sr 4:0:0:0: Attached scsi generic sg1 type 5
    SCSI Media Changer driver v0.25 
    PCI: Enabling device 0000:00:1d.7 (0000 -> 0002)
    ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 201
    PCI: Setting latency timer of device 0000:00:1d.7 to 64
    ehci_hcd 0000:00:1d.7: EHCI Host Controller
    ehci_hcd 0000:00:1d.7: debug port 1
    PCI: cache line size of 32 is not supported by device 0000:00:1d.7
    ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
    ehci_hcd 0000:00:1d.7: irq 201, io mem 0x88405400
    ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
    usb usb1: configuration #1 chosen from 1 choice
    hub 1-0:1.0: USB hub found
    hub 1-0:1.0: 8 ports detected
    ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
    USB Universal Host Controller Interface driver v2.3
    ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 201
    PCI: Setting latency timer of device 0000:00:1d.0 to 64
    uhci_hcd 0000:00:1d.0: UHCI Host Controller
    uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
    uhci_hcd 0000:00:1d.0: irq 201, io base 0x000030a0
    usb usb2: configuration #1 chosen from 1 choice
    hub 2-0:1.0: USB hub found
    hub 2-0:1.0: 2 ports detected
    ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 185
    PCI: Setting latency timer of device 0000:00:1d.1 to 64
    uhci_hcd 0000:00:1d.1: UHCI Host Controller
    uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
    uhci_hcd 0000:00:1d.1: irq 185, io base 0x00003080
    usb usb3: configuration #1 chosen from 1 choice
    hub 3-0:1.0: USB hub found
    hub 3-0:1.0: 2 ports detected
    ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 193
    PCI: Setting latency timer of device 0000:00:1d.2 to 64
    uhci_hcd 0000:00:1d.2: UHCI Host Controller
    uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
    uhci_hcd 0000:00:1d.2: irq 193, io base 0x00003060
    usb 1-4: new high speed USB device using ehci_hcd and address 3
    usb usb4: configuration #1 chosen from 1 choice
    hub 4-0:1.0: USB hub found
    hub 4-0:1.0: 2 ports detected
    ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 16 (level, low) -> IRQ 169
    PCI: Setting latency timer of device 0000:00:1d.3 to 64
    uhci_hcd 0000:00:1d.3: UHCI Host Controller
    uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
    uhci_hcd 0000:00:1d.3: irq 169, io base 0x00003040
    usb usb5: configuration #1 chosen from 1 choice
    hub 5-0:1.0: USB hub found
    hub 5-0:1.0: 2 ports detected
    usb 1-4: configuration #1 chosen from 1 choice
    Initializing USB Mass Storage driver...
    usb 2-1: new full speed USB device using uhci_hcd and address 2
    usb 2-1: configuration #1 chosen from 1 choice
    hub 2-1:1.0: USB hub found
    hub 2-1:1.0: 3 ports detected
    usb 5-1: new full speed USB device using uhci_hcd and address 2
    usb 5-1: configuration #1 chosen from 1 choice
    usb 5-2: new full speed USB device using uhci_hcd and address 3
    usb 5-2: configuration #1 chosen from 1 choice
    usb 2-1.2: new low speed USB device using uhci_hcd and address 3
    usb 2-1.2: configuration #1 chosen from 1 choice
    usb 2-1.3: new full speed USB device using uhci_hcd and address 4
    usb 2-1.3: configuration #1 chosen from 1 choice
    usbcore: registered new driver usb-storage
    USB Mass Storage support registered.
    input: USB HIDBP Keyboard 05ac:1000 as /class/input/input0
    input: Mitsumi Electric Apple Extended USB Keyboard as /class/input/input1
    usbcore: registered new driver usbkbd
    drivers/usb/input/usbkbd.c: :USB HID Boot Protocol keyboard driver
    input: USB HIDBP Mouse 05ac:1000 as /class/input/input2
    input: MOUSE SYSTEM U+P OPTICAL MOUSE as /class/input/input3
    usbcore: registered new driver usbmouse
    drivers/usb/input/usbmouse.c: v1.6:USB HID Boot Protocol mouse driver
    mice: PS/2 mouse device common for all mice
    EFI Variables Facility v0.08 2004-May-17
    NET: Registered protocol family 2
    IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
    TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
    TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
    TCP: Hash tables configured (established 131072 bind 65536)
    TCP reno registered
    TCP bic registered
    NET: Registered protocol family 1
    NET: Registered protocol family 17
    Starting balanced_irq
    Using IPI Shortcut mode
    ReiserFS: sda5: found reiserfs format "3.6" with standard journal
    ReiserFS: sda5: using ordered data mode
    ReiserFS: sda5: journal params: device sda5, size 8192, journal first block 18, 
                    max trans len 1024, max batch 900, max commit age 30, max trans age 30
    ReiserFS: sda5: checking transaction log (sda5)
    ReiserFS: sda5: Using r5 hash to sort names
    VFS: Mounted root (reiserfs filesystem) readonly.
    Freeing unused kernel memory: 248k freed
    Adding 1048568k swap on /dev/sda4.  Priority:-1 extents:1 across:1048568k
    Linux agpgart interface v0.101 (c) Dave Jones
    agpgart: Detected an Intel 945GM Chipset.
    agpgart: AGP aperture is 256M @ 0x0
    shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
    PCI: Enabling device 0000:00:1b.0 (0000 -> 0002)
    ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 22 (level, low) -> IRQ 209
    PCI: Setting latency timer of device 0000:00:1b.0 to 64
    ieee1394: Initialized config rom entry `ip1394'
    ACPI: PCI Interrupt 0000:04:03.0[A] -> GSI 19 (level, low) -> IRQ 185
    ohci1394: fw-host0: Unexpected PCI resource length of 1000!
    ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[185]  MMIO=[88000000-880007ff]
                                             Max Packet=[2048]  IR/IT contexts=[8/8]
    ieee1394: Host added: ID:BUS[0-00:1023]  GUID[001451fffeb7203e]
    sky2 eth0: enabling interface
    sky2 eth0: Link is up at 100 Mbps, full duplex, flow control none
    Using specific hotkey driver
    ACPI: AC Adapter [ADP1] (on-line)
    ACPI: CPU0 (power states: C1[C1] C2[C2])
    ACPI: Processor [CPU0] (supports 8 throttling states)
    ACPI: CPU1 (power states: C1[C1] C2[C2])
    ACPI: Processor [CPU1] (supports 8 throttling states)
    ACPI: Power Button (FF) [PWRF]
    ACPI: Power Button (CM) [PWRB]
    ACPI Error (evgpe-0688): No handler or method for GPE[1D], disabling event [20060127]
    ACPI: Video Device [GFX0] (multi-head: yes  rom: no  post: no)
    Bluetooth: Core ver 2.8
    NET: Registered protocol family 31
    Bluetooth: HCI device and connection manager initialized
    Bluetooth: HCI socket layer initialized
    Bluetooth: L2CAP ver 2.8
    Bluetooth: L2CAP socket layer initialized
    Bluetooth: RFCOMM socket layer initialized
    Bluetooth: RFCOMM TTY layer initialized
    Bluetooth: RFCOMM ver 1.7
    
  • vmware
    vmmon: module license 'unspecified' taints kernel.
    /dev/vmmon[5996]: Module vmmon: registered with major=10 minor=165
    /dev/vmmon[5996]: Module vmmon: initialized
    /dev/vmmon[6009]: Module vmmon: unloaded
    /dev/vmmon[6278]: Module vmmon: registered with major=10 minor=165
    /dev/vmmon[6278]: Module vmmon: initialized
    /dev/vmnet: open called by PID 6311 (vmnet-bridge)
    /dev/vmnet: hub 0 does not exist, allocating memory.
    /dev/vmnet: port on hub 0 successfully opened
    bridge-eth0: enabling the bridge
    bridge-eth0: up
    bridge-eth0: already up
    bridge-eth0: attached
    /dev/vmnet: open called by PID 6315 (vmnet-bridge)
    /dev/vmnet: hub 2 does not exist, allocating memory.
    /dev/vmnet: port on hub 2 successfully opened
    bridge-dummy0: peer interface dummy0 not found, will wait for it to come up
    bridge-dummy0: attached
    




トップ   編集 凍結 差分 バックアップ 添付 複製 名前変更 リロード   新規 一覧 単語検索 最終更新   ヘルプ   最終更新のRSS
Last-modified: 2006-06-13 (火) 20:02:26 (6717d)